10/9/2021 0 Comments Mikrotik Wireless Bridge Setup
There, make a new profile with the Add button and set desired WPA2 settings. You can choose this new security profile back in the Interface configuration.To see if any stations are connected to your AP, go to the Registration Table tab in the Wireless Interface window.Just connecting is probaly not enough, as your AP needs an IP address. This can be configured in the IP menu. Make sure that your stations also have IP addresses from the same subnet, or set up a DHCP server in this Router (not covered in this tutorial).If your ISP doesn't know about your new local network and hasn't set up proper routes to it, you need to configure SRC-NAT so that your stations have access to the internet via their private IP addresses. A connection to the router via the Winbox utilityStart by opening the Wireless Interface window in Winbox. You will see some wireless cards listed here, they might be disabled - to turn them on, click on the blue Enable button.Now I'm setting them up so that they are all a part of one network with the same ID so that NAS and Plex server are accessible all over the house.There is an ISP's router with IP: 192.168.64.1 (I think this one also has a wifi option, but it has been disabled since the beginning and I'm not sure why. This router has so many settings in so many tabs that I have no clue what I'm supposed to set and what I should leave untouched.We have 3 wifi routers in the house and until now they have all been working with their own network and their own ID. Well at least not in quite the way I want to. Yesterday I've spent 4 hours trying to set this router as an AP, but with no success. You can also set other things, like the desired band, frequency, SSID (the AP identifier) and the security profile.You probably want your AP to be secure, so you need to configure WPA2 security.(while I'm setting it up I'm connected directly to LAN port 2 with my PC and the GUI opens up on tplinklogin.net ) after I set it up, I connect the AP1 with MAIN on that same LAN port - leaving the WAN empty.The only thing that makes me think this setup is working is that I have a TV box connected to this router and it's working. I might just be connecting to the MAIN since the the routers are again not that far from each other (AP1 in on ground flour and MAIN is on 1st flour right above it).And the thing is that once I do this setup i can't access the AP1s Web GUI anymore. I think Since the SSIDs are the same on both and the AP doesn't have DHCP with it's own network I'm not really sure. It's set up with DHCP range from 2-254AP #1 (older tp-link router): On this one I set a static IP 192.168.1.2 with gateway to 192.168.1.1 and DHCP disabled and it has the same SSID as the MAIN <- this configuration works.I factory reset my AP2 and connect to it on 192.168.88.1 over ethernet on LAN2. I wanted it to have a fixed IP address of 192.168.1.3 so under the DHCP tab on the MAIN I set it up with that IP. The web GUI doesn't open up if I enter that IP (while connected directly to AP1 with cable)OK, so on the main router I see the MikroTik router(AP2) with the host name MikroTik. The third (unknown) device with IP 192.168.0.1 I think is the AP1 since that is the IP i think I saw during the setup. 145 are , but they might be the WiFi switches my brother is playing around with (you know for turning on/off lights and such). (Devices get an IP from the MAIN's dhcp) this is a screenshot of the connection list on the MAIN router I'm not sure what are the two (unknown) devices on.
![]() The router always acquires 1.26 and uses dhcp with 88.1 for all the devices connected to it. But I still don't see the NAS or the Plex server on my network.Please do help me navigate trough this mess.Also is there an option to change the firmware on the mikrotik router? To something easier, openwrt or whatever is the go-to option right now I've used dd-wrt in the past and right now on the Main router there is Gargoyle installed (My brother was always the one changing the firmware on routers but for a few years now he just won't touch the networking in this house and I haven't installed firmware on a router before)Under local network I disable the DHCP - I've tried leaving IP address under Local network as 192.168.88.1 or changing it to 192.168.1.3 - both options (coupled with the changing to static ip addres s) results in loss of connec tion to t he internet and I cannot access the routers GUI on any of the IPs - after that I just have to reset the router again <- this is the configuration at this moment. So on the computer I'm writing this post on I get the IP address 192.168.88.254With this configuration i can access the main router's GUI on 192.168.1.1 which as far as I know, you can't do unless you are on the same network. The router always acquires 1.26 and uses dhcp with 88.1 for all the devices connected to it. In the main tab of MikroTiks web GUI (Quick Set) I want to set the acquired IP address to 192.168.1.3 with gateway to 1.1.Under local network I disable the DHCP - I've tried leaving IP address under Local network as 192.168.88.1 or changing it to 192.168.1.3 - both options (coupled with the changing to static ip address) results in loss of connection to the internet and I cannot access the routers GUI on any of the IPs - after that I just have to reset the router again <- this is the configuration at this moment. On MikroTik I gave it a static IP under Internet and the same IP on the Local network, disabled DHCP and NAT.Now my desktop is getting an IP from the MAIN router's DHCP range, but I again lost the ability to enter the web GUI of the access point.I think its 6.22, but I can't check because I can't access the webGUI anymore. 9 to different devices.I've fixed the DHCP range and deleted the static ip on the MAIN. I'm not that familiar with configuring MikroTik devices, but there seems to be good & simple documentation on setting it as an AP.If it's just a router, why do you have it? If it's a modem with fibre, coax or xDSL coming to it from ISP, then it's probably set in bridge mode & all features disabled.The DHCP range shouldn't overlap with the statically assigned addresses and not sure why your router even allows you to do that.Change the DHCP range to something like 10-254 so you can assign from. Should be disabled when setting up as a wireless bridge. On the MikroTik, all other features such as NAT, DHCP, firewall etc. Let’s say you reset it to defaults, here are the main steps:-Connect the uplink to ether1 and your computer to ether2.-change the master-port of ether3-ether5 from ether2 to ether1 (this setting is under Interfaces). In 6.22 this is done via the Master Port setting. You want to change the configuration so that all 5 ports are treated as LAN, and there is only a single IP assignment. They do have the Quick Set function that can be used to pick a premade profile, which might be useful for you but they aren’t perfect and the function of Quick Set depends also on your version. You should be get DHCP from 192.168.1.1, be online, and be able to access the Mikrotik settings at its 192.168.1.x IP that is assigned by DHCP or statically-while connected to the wireless or ether3-ether5, access the settings for the remaining steps:-remove the IP>Address and IP>DHCP Server from ether2-change the ether2 Master Port from none to ether1-ether2 should now function the same as ether3-ether5Here is a summary of the final setup that should be achieved:-all 5 ethernet ports connected together via the switch chip (achieved by assigning ether2-ether5 to have ether1 as the master port)-a DHCP client or static IP assigned on said bridge-the single connection and IP is treated as LAN, not WAN-all other config needed for router use (DHCP Server, Masquerade rule, etc) removedBy the way, while doing major changes it is helpful to use Safe Mode: Also if you haven’t use Winbox yet, give it a try, it is much better for seeing multiple settings at once: Mikrotik is complicated because every device is capable of so many things, and there isn’t much in the way of automatic functionality. Alternatively, delete the DHCP client, and statically assign an IP in IP>Addresses to the bridge-if there was a bridge already and you removed ether2 from it, then move the IP > DHCP server from the bridge to ether2, and also the IP>Address 192.168.88.1 to ether2-change the firewall settings (IP > Firewall) so ether1 is treated as LAN - you can basically get rid of all of the rules that are there by default because you aren’t going to be forwarding and you want to accept inputs.-remove the Masquerade rule from IP>Firewall>NAT - this is what does the outbound NAT-test wireless and wired on ether3-ether5.
0 Comments
Leave a Reply. |
AuthorNicole ArchivesCategories |